Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Do not undervalue the forklift at work. If the procedure is not good, there will be significant crashes in mins, and there are lots of crashes entailing forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the individual in front can not be discovered, causing a rolling mishap.
Case 2: In order to preserve the equilibrium of the forklift when raising hefty items, the employees utilized their body weight as the counterweight, which nearly caused casualties.
Situation 3: The size of the forklift freight surpasses the allowable size of the path and hangs on the roadside rack, which virtually creates an accident.
Situation 4: Forklift is speeding up and rolls over during a turn.
Situation 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the workers unlawfully, the forklift driver does not put on the safety belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Case 7: The forklift driver did not wear a safety belt and dropped from the lorry when it rolled over and was crushed.
Forklift operation ought to take notice of these issues ：.

Begin.
1. Before starting, observe the surroundings, and after verifying that there are no barriers that prevent the safety and security of driving, beep the horn initially and afterwards begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be secure prior to starting.
3. When the forklift begins with a tons, the vehicle driver needs to initially validate that the lots is stable and reputable.
4. The beginning has to be sluggish and stable.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backwards. .
2. Do not lift the fork too high when driving. When entering and leaving the task site or while driving, be careful that there will be no barriers in the sky. When the load is traveling, the fork should not be elevated too expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork needs to be lowered to the regular driving position prior to driving. .
4. When transforming, if there are pedestrians or vehicles close by, the driving signal should be issued initially. High-speed doglegs are prohibited. High-speed sharp turns will cause the lorry to shed lateral stability and topple. .
5. When the forklift is downhill, it is purely prohibited to switch off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to follow the traffic rules in the factory and should keep a certain safety and security distance from the automobile in front. .
7. When the forklift is running, the load should be in the lowest setting that does not hinder the driving, and the gantry ought to be correctly slanted back. The load shall not be elevated other than when piling or filling. .
8. The elevation of the lots should not block the chauffeur's view. In unique conditions, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The risk-free driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a low speed when entering the production workshop area. .
11. When the forklift is raised, lifted or driven, it is prohibited for workers to stand on the fork to hold items and play a stabilizing duty. .
12. If troubles are located, they will certainly be repaired and reported in a timely way, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range in between the two forks must be changed as needed to make the tons of the two forks balanced and not manipulated, and one side of the item should be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special circumstances, security indication should be set up to advise surrounding pedestrians. .
3. In the process of packing and dumping items, the forklift has to be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm people. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as feasible under the lots, and it must be noted that the fork suggestion must not touch other products or things. The tons must be maintained with very little back tilt of the gantry to make sure that the lots does not move in reverse. The mast can be tilted ahead somewhat when the lots is decreased to allow for very easy positioning of the tons and extraction of the forks. .
6. It is forbidden to fork items at high speed and hit difficult objects with the fork head. .
7. When the forklift is working, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overwhelming is banned, and it is banned to utilize forks to raise workers to take part in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not enabled to utilize the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to make use of forks to select, transform pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the items on the fork are in the air. Prior to leaving the forklift, you have to dump the goods or lower the fork structure.
2. Draw the emergency brake take care of to dead or depress the hand brake button.
3. The engine is turned off and the power is removed. (Except for special circumstances, such as the motorist does not leave the car's view and does not surpass 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubricating oil and air conditioning water ought to be included.
2. Inspect the security performance of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. During the procedure of the forklift, examine whether the stress and temperature are regular.
5. After the forklift is running, the external leak needs to also be examined and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the automobile;.
2. When you experience someone in front of you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be too sharp to avoid the propensity of " totally free switching";.
6. Running up and down the slope must be slow and uniform, and no switching on the slope is allowed.
7. Do not drive throughout the slope. When the gradient is higher than 10%, the vehicle needs to be driven in reverse when declining;.
8. When the forklift personnel lug the goods and move forward, if they encounter big or heavy items and most likely to the vehicle Electric Forklift Truck for Warehouse driver's view, they should Electric Forklift Truck for Warehouse take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not permitted.
2. It is not permitted to raise the goods for cross country driving.
3. It is not allowed to pick up the goods by turning over the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to use inertia force to pick up the goods.
6. It is not allowed to use braking force to expatriation round or easy-to-roll things.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the same length as the obstacle need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844